lede-packages-rs

apcupsd.conf (11805B)

---

 ## apcupsd.conf v1.1 ##
 # 
 #  for apcupsd release 3.14.1 (04 May 2007) - unknown
 #
 # "apcupsd" POSIX config file
 
 #
 # ========= General configuration parameters ============
 #
 
 # UPSNAME xxx
 #   Use this to give your UPS a name in log files and such. This
 #   is particularly useful if you have multiple UPSes. This does not
 #   set the EEPROM. It should be 8 characters or less.
 UPSNAME ups1
 
 # UPSCABLE <cable>
 #   Defines the type of cable connecting the UPS to your computer.
 #
 #   Possible generic choices for <cable> are:
 #     simple, smart, ether, usb
 #
 #   Or a specific cable model number may be used:
 #     940-0119A, 940-0127A, 940-0128A, 940-0020B,
 #     940-0020C, 940-0023A, 940-0024B, 940-0024C,
 #     940-1524C, 940-0024G, 940-0095A, 940-0095B,
 #     940-0095C, M-04-02-2000
 #
 UPSCABLE smart
 
 # To get apcupsd to work, in addition to defining the cable
 # above, you must also define a UPSTYPE, which corresponds to
 # the type of UPS you have (see the Description for more details).
 # You must also specify a DEVICE, sometimes referred to as a port.
 # For USB UPSes, please leave the DEVICE directive blank. For
 # other UPS types, you must specify an appropriate port or address.
 #
 # UPSTYPE   DEVICE           Description
 # apcsmart  /dev/tty**       Newer serial character device,
 #                            appropriate for SmartUPS models using
 #                            a serial cable (not USB).
 #
 # usb       <BLANK>          Most new UPSes are USB. A blank DEVICE
 #                            setting enables autodetection, which is
 #                            the best choice for most installations.
 #
 # net       hostname:port    Network link to a master apcupsd
 #                            through apcupsd's Network Information
 #                            Server. This is used if you don't have
 #                            a UPS directly connected to your computer.
 #
 # snmp      hostname:port:vendor:community
 #                            SNMP Network link to an SNMP-enabled
 #                            UPS device. Vendor is the MIB used by
 #                            the UPS device: can be "APC", "APC_NOTRAP"
 #                            or "RFC" where APC is the powernet MIB,
 #                            "APC_NOTRAP" is powernet with SNMP trap
 #                            catching disabled, and RFC is the IETF's 
 #                            rfc1628 UPS-MIB. You usually want "APC".
 #                            Port is usually 161. Community is usually
 #                            "private".
 #
 # dumb      /dev/tty**       Old serial character device for use 
 #                            with simple-signaling UPSes.
 #
 # pcnet    ipaddr:username:passphrase
 #                            PowerChute Network Shutdown protocol
 #                            which can be used as an alternative to SNMP
 #                            with AP9617 family of smart slot cards.
 #                            ipaddr is the IP address of the UPS mgmt
 #                            card. username and passphrase are the
 #                            credentials for which the card has been
 #                            configured.
 #
 UPSTYPE apcsmart
 DEVICE /dev/ttyS0
 
 
 # LOCKFILE <path to lockfile>
 #   Path for device lock file. Not used on Win32.
 LOCKFILE /var/lock
 
 # SCRIPTDIR <path to script directory>
 #   Directory in which apccontrol and event scripts are located.
 SCRIPTDIR /etc/apcupsd
 
 # PWRFAILDIR <path to powerfail directory>
 #   Directory in which to write the powerfail flag file. This file
 #   is created when apcupsd initiates a system shutdown and is
 #   checked in the OS halt scripts to determine if a killpower
 #   (turning off UPS output power) is required.
 PWRFAILDIR /etc
 
 # NOLOGINDIR <path to nologin directory>
 #   Directory in which to write the nologin file. The existence
 #   of this flag file tells the OS to disallow new logins.
 NOLOGINDIR /etc
 
 
 #
 # ======== Configuration parameters used during power failures ==========
 #
 
 # The ONBATTERYDELAY is the time in seconds from when a power failure
 #   is detected until we react to it with an onbattery event.
 #
 #   This means that, apccontrol will be called with the powerout argument
 #   immediately when a power failure is detected.  However, the
 #   onbattery argument is passed to apccontrol only after the 
 #   ONBATTERYDELAY time.  If you don't want to be annoyed by short
 #   powerfailures, make sure that apccontrol powerout does nothing
 #   i.e. comment out the wall.
 #ONBATTERYDELAY 6
 
 # 
 # Note: BATTERYLEVEL, MINUTES, and TIMEOUT work in conjunction, so
 # the first that occurs will cause the initiation of a shutdown.
 #
 
 # If during a power failure, the remaining battery percentage
 # (as reported by the UPS) is below or equal to BATTERYLEVEL, 
 # apcupsd will initiate a system shutdown.
 BATTERYLEVEL 5
 
 # If during a power failure, the remaining runtime in minutes 
 # (as calculated internally by the UPS) is below or equal to MINUTES,
 # apcupsd, will initiate a system shutdown.
 MINUTES 3
 
 # If during a power failure, the UPS has run on batteries for TIMEOUT
 # many seconds or longer, apcupsd will initiate a system shutdown.
 # A value of 0 disables this timer.
 #
 #  Note, if you have a Smart UPS, you will most likely want to disable
 #    this timer by setting it to zero. That way, you UPS will continue
 #    on batteries until either the % charge remaining drops to or below BATTERYLEVEL,
 #    or the remaining battery runtime drops to or below MINUTES.  Of course,
 #    if you are testing, setting this to 60 causes a quick system shutdown
 #    if you pull the power plug.   
 #  If you have an older dumb UPS, you will want to set this to less than
 #    the time you know you can run on batteries.
 TIMEOUT 0
 
 #  Time in seconds between annoying users to signoff prior to
 #  system shutdown. 0 disables.
 ANNOY 300
 
 # Initial delay after power failure before warning users to get
 # off the system.
 ANNOYDELAY 60
 
 # The condition which determines when users are prevented from
 # logging in during a power failure.
 # NOLOGON <string> [ disable | timeout | percent | minutes | always ]
 NOLOGON disable
 
 # If KILLDELAY is non-zero, apcupsd will continue running after a
 # shutdown has been requested, and after the specified time in
 # seconds attempt to kill the power. This is for use on systems
 # where apcupsd cannot regain control after a shutdown.
 # KILLDELAY <seconds>  0 disables
 KILLDELAY 0
 
 #
 # ==== Configuration statements for Network Information Server ====
 #
 
 # NETSERVER [ on | off ] on enables, off disables the network
 #  information server. If netstatus is on, a network information
 #  server process will be started for serving the STATUS and
 #  EVENT data over the network (used by CGI programs).
 NETSERVER on
 
 # NISIP <dotted notation ip address>
 #  IP address on which NIS server will listen for incoming connections.
 #  This is useful if your server is multi-homed (has more than one
 #  network interface and IP address). Default value is 0.0.0.0 which
 #  means any incoming request will be serviced. Alternatively, you can
 #  configure this setting to any specific IP address of your server and 
 #  NIS will listen for connections only on that interface. Use the
 #  loopback address (127.0.0.1) to accept connections only from the
 #  local machine.
 NISIP 0.0.0.0
 
 # NISPORT <port> default is 3551 as registered with the IANA
 #  port to use for sending STATUS and EVENTS data over the network.
 #  It is not used unless NETSERVER is on. If you change this port,
 #  you will need to change the corresponding value in the cgi directory
 #  and rebuild the cgi programs.
 NISPORT 3551
 
 # If you want the last few EVENTS to be available over the network
 # by the network information server, you must define an EVENTSFILE.
 EVENTSFILE /var/log/apcupsd.events
 
 # EVENTSFILEMAX <kilobytes>
 #  By default, the size of the EVENTSFILE will be not be allowed to exceed
 #  10 kilobytes.  When the file grows beyond this limit, older EVENTS will
 #  be removed from the beginning of the file (first in first out).  The
 #  parameter EVENTSFILEMAX can be set to a different kilobyte value, or set
 #  to zero to allow the EVENTSFILE to grow without limit.
 EVENTSFILEMAX 10
 
 #
 # ========== Configuration statements used if sharing =============
 #            a UPS with more than one machine
 
 # NETTIME <int>
 #   Interval (in seconds) at which the NIS client polls the server.
 #   Used only when this apcupsd is a network client (UPSTYPE net).
 #NETTIME 60
 
 #
 # Remaining items are for ShareUPS (APC expansion card) ONLY
 #
 
 # UPSCLASS [ standalone | shareslave | sharemaster ]
 #   Normally standalone unless you share an UPS using an APC ShareUPS
 #   card.
 UPSCLASS standalone
 
 # UPSMODE [ disable | share ]
 #   Normally disable unless you share an UPS using an APC ShareUPS card.
 UPSMODE disable
 
 #
 # ===== Configuration statements to control apcupsd system logging ========
 #
 
 # Time interval in seconds between writing the STATUS file; 0 disables
 STATTIME 0
 
 # Location of STATUS file (written to only if STATTIME is non-zero)
 STATFILE /var/log/apcupsd.status
 
 # LOGSTATS [ on | off ] on enables, off disables
 # Note! This generates a lot of output, so if         
 #       you turn this on, be sure that the
 #       file defined in syslog.conf for LOG_NOTICE is a named pipe.
 #  You probably do not want this on.
 LOGSTATS off
 
 # Time interval in seconds between writing the DATA records to
 #   the log file. 0 disables.
 DATATIME 0
 
 # FACILITY defines the logging facility (class) for logging to syslog. 
 #          If not specified, it defaults to "daemon". This is useful 
 #          if you want to separate the data logged by apcupsd from other
 #          programs.
 #FACILITY DAEMON
 
 #
 # ========== Configuration statements used in updating the UPS EPROM =========
 #
 
 #
 # These statements are used only by apctest when choosing "Set EEPROM with conf
 # file values" from the EEPROM menu. THESE STATEMENTS HAVE NO EFFECT ON APCUPSD.
 #
 
 # UPS name, max 8 characters 
 #UPSNAME UPS_IDEN
 
 # Battery date - 8 characters
 #BATTDATE mm/dd/yy
 
 # Sensitivity to line voltage quality (H cause faster transfer to batteries)  
 # SENSITIVITY H M L        (default = H)
 #SENSITIVITY H
 
 # UPS delay after power return (seconds)
 # WAKEUP 000 060 180 300   (default = 0)
 #WAKEUP 60
 
 # UPS Grace period after request to power off (seconds)
 # SLEEP 020 180 300 600    (default = 20)
 #SLEEP 180
 
 # Low line voltage causing transfer to batteries
 # The permitted values depend on your model as defined by last letter 
 #  of FIRMWARE or APCMODEL. Some representative values are:
 #    D 106 103 100 097
 #    M 177 172 168 182
 #    A 092 090 088 086
 #    I 208 204 200 196     (default = 0 => not valid)
 #LOTRANSFER  208
 
 # High line voltage causing transfer to batteries
 # The permitted values depend on your model as defined by last letter 
 #  of FIRMWARE or APCMODEL. Some representative values are:
 #    D 127 130 133 136
 #    M 229 234 239 224
 #    A 108 110 112 114
 #    I 253 257 261 265     (default = 0 => not valid)
 #HITRANSFER 253
 
 # Battery charge needed to restore power
 # RETURNCHARGE 00 15 50 90 (default = 15)
 #RETURNCHARGE 15
 
 # Alarm delay 
 # 0 = zero delay after pwr fail, T = power fail + 30 sec, L = low battery, N = never
 # BEEPSTATE 0 T L N        (default = 0)
 #BEEPSTATE T
 
 # Low battery warning delay in minutes
 # LOWBATT 02 05 07 10      (default = 02)
 #LOWBATT 2
 
 # UPS Output voltage when running on batteries
 # The permitted values depend on your model as defined by last letter 
 #  of FIRMWARE or APCMODEL. Some representative values are:
 #    D 115
 #    M 208
 #    A 100
 #    I 230 240 220 225     (default = 0 => not valid)
 #OUTPUTVOLTS 230
 
 # Self test interval in hours 336=2 weeks, 168=1 week, ON=at power on
 # SELFTEST 336 168 ON OFF  (default = 336)
 #SELFTEST 336